Campbell CR23X Spécifications Page 343
- Page / 374
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AD-11-1
SECTION 11. OUTPUT PROCESSING INSTRUCTIONS
Instructions 73 – Maximum and 74 – Minimum have only one time option. (Time is output as a quoted
string.) Instruction 80 – Set Active Storage Area, is not in the TD operating system. Its functions are
included in Instruction 84 – Data Table. Instruction 84 is only in the TD operating system.
*** 73 MAXIMUM ***
FUNCTION
This instruction stores the MAXIMUM value
tak
en (f
or each input location specified) over
a given output interval. An internal FLAG is
set whenever a new maximum value is seen.
This FLAG may be tested by Instruction 79.
Time of occurrence maximum value(s) is
OPTIONAL output information, which is
formatted and activated by entering one of
the following CODES for Parameter no. 2.
CODE OPTIONS
00 Output value ONLY
01 Output value with TIME
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 2 Repetitions
02: 2 Time of maximum
(
optional)
03:
4 Starting input location no.
Outputs Generated: 1 for each input location
(
plus 1 w
ith time of max. option)
*** 74 MINIMUM ***
FUNCTION
Operating in the same manner as Program 73,
this
inst
ruction is used for storing the MINIMUM
value (for each input location specified) over a
given output interval.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 2 Repetitions
02: 2 Time of minimum
(
optional)
03:
4 Starting input location no.
Outputs Generated: 1 for each input location
(
plus 1 w
ith time of min. option)
*** 84 DATA TABLE ***
FUNCTION
Instruction 84 is used to define a table of final
s
tor
age data. New records of data are stored in
the table based on time (interval data) or when
a user flag (CR10X flags 1-8) is set (event
data). Time based output intervals are
specified in seconds. Fractional values may be
used following the same rules that apply for the
table scan rate.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: FP Time into interval (Seconds)
02: FP Time interval (Seconds)
0 = Store new record
eac
h time.
-
a = Store if user flag
"a" is
set (a=1..8)
03:
FP Number of records in table
0 = automatically allocates
num
ber of
records.
If 0 and parameter 2 = -a
(
event driven)
or if 0 and
parameter 2 = 0 then
allocates size as if a 1
second output table
-x = redirect to input loc x
Parameter 1 specifies how many seconds into
the inter
val, s
pecified in parameter 2, data will
be output to final storage. If the output is event
driven, enter a 0 for parameter 1.
Parameter 2 specifies the output interval
(
sec
onds) for the table. If output is determined
by a flag, -a should be used, ('a' is the flag to
be tested). If Parameter 2 = 0, data will be
output unconditionally each time Instruction 84
is executed.
Parameter 3 specifies how many records will be
s
tor
ed in the table. When the table is full,
subsequent new records will overwrite the oldest
- CR23X Micrologge 1
- Warranty and Assistance 2
- TABLE OF CONTENTS 3
- DATA RETRIEVAL/COMMUNICATION 4
- PROGRAM EXAMPLES 4
- INSTRUCTIONS 5
- INSTALLATION 6
- APPENDICES 6
- CR23X MANUALS 7
- CR23X TABLE OF CONTENTS 8
- SELECTED OPERATING DETAILS 9
- CAUTIONARY NOTES 10
- CR23X MICROLOGGER OVERVIEW 11
- CR23X MICROLOGGER 13
- OV2. MEMORY AND PROGRAMMING 15
- CONCEPTS 15
- OV4. PROGRAMMING THE CR23X 23
- OV5. PROGRAMMING EXAMPLES 24
- OV6. DATA RETRIEVAL OPTIONS 31
- OV7. SPECIFICATIONS 33
- 1.5 MEMORY ALLOCATION 39
- FIGURE 1.5-1. CR23X Memory 41
- STATUS 43
- MODE -- SECURITY 45
- MODE -- SAVE OR LOAD 45
- ARRAYS, AND MEMORY POINTERS 51
- 3.1 PARAMETER DATA TYPES 55
- 3.2 REPETITIONS (Reps) 55
- CONTROL PORTS 55
- 3.5 VOLTAGE RANGE AND 56
- OVERRANGE DETECTION 56
- 3.6 OUTPUT PROCESSING 56
- PROGRAM CONTROL 57
- 3.8 PROGRAM CONTROL LOGICAL 58
- CONSTRUCTIONS 58
- 3.9 INSTRUCTION MEMORY AND 59
- EXECUTION TIME 59
- 3.10 ERROR CODES 63
- 4.1 ON-LINE DATA TRANSFER 65
- INSTRUCTION 96 65
- 4.2 MANUALLY INITIATED DATA 67
- OUTPUT 67
- 4.3 PRINTER OUTPUT FORMATS 67
- 4.4 STORAGE MODULE 68
- 5.1 TELECOMMUNICATIONS 73
- COMMANDS 73
- (OPTICALLY ISOLATED) 79
- 6.3 USE OF INSTRUCTION 96 87
- 7.1 SINGLE-ENDED VOLTAGE/ 89
- 7.5 107 TEMPERATURE PROBE 92
- 7.6 ANEMOMETER WITH 92
- PHOTOCHOPPER OUTPUT 92
- WITH LONG LEADS 93
- 7.11 PRESSURE TRANSDUCER - 4 96
- WIRE FULL BRIDGE 96
- 7.12 LYSIMETER - 6 WIRE FULL 97
- 7.14 NONLINEAR THERMISTOR IN 100
- HALF BRIDGE (CAMPBELL 100
- SCIENTIFIC MODEL 101) 100
- CR23X & AVW1 103
- PRESSURE TRANSDUCER 105
- CONNECTIONS 107
- CURS100 TERMINAL INPUT 108
- 7.17 4 TO 20 MA SENSOR USING 108
- 12V Power Out 109
- This is a blank page 110
- 8.1 COMPUTATION OF RUNNING 111
- 8.2 RAINFALL INTENSITY 112
- 8.3 USING CONTROL PORTS AND 113
- LOOP TO RUN AM416 113
- MULTIPLEXER 113
- SYNCHED TO REAL TIME 115
- PORTS (RAIN GAGE) 115
- 8.6 SDM-A04 ANALOG OUTPUT 116
- MULTIPLEXER TO STRIP CHART 116
- 8.7 CONVERTING 0-360 WIND 117
- DIRECTION OUTPUT TO 0-540 FOR 117
- STRIP CHART 117
- - SAVING DATA PRIOR TO EVENT 118
- 8.10 COVARIANCE CORRELATION 121
- PROGRAMMING EXAMPLE 121
- 04: Z=X*F (P37) 123
- 8.11 FAST FOURIER TRANSFORM 125
- EXAMPLES 125
- POWER SENSORS 132
- Silicon diodes 152
- Parameters 6 155
- Input locations altered: 1 160
- This is a blankpage 164
- This is a blankp age 188
- SEQUENCE 201
- 16.67 mS 60 Hz Reject 202
- 20.00 mS 50 Hz Reject 202
- LENGTH ON THE SIGNAL SETTLING 204
- HI OR LO 205
- (/((.(-45 0* * * * + * * 208
- 10 610 3310 4110 1000 208
- 13.5 BRIDGE RESISTANCE 220
- MEASUREMENTS 220
- 13.6 RESISTANCE MEASUREMENTS 224
- REQUIRING AC EXCITATION 224
- 13.7 CALIBRATION PROCESS 225
- 14.1 PROTECTION FROM THE 227
- ENVIRONMENT 227
- 14.2 POWER REQUIREMENTS 228
- 10 D-TYPE ALKALINE BATTERIES 230
- 14.4 SOLAR PANELS 231
- TO THE CR23X WIRING PANEL 232
- 14.6 VEHICLE POWER SUPPLY 232
- 14.7 CR23X Grounding 233
- 14.8 POWERING SENSORS AND 235
- PERIPHERALS 235
- 14.9 CONTROLLING POWER TO 236
- SENSORS AND PERIPHERALS 236
- 14.10 MAINTENANCE 237
- APPENDIX A. GLOSSARY 241
- B.1 SPECIFICATIONS 245
- B.3 INSTRUCTION 15 AND 246
- PARAMETER DESCRIPTIONS 246
- AND SENSOR WIRING 249
- B.5 RS-232 SERIAL DATA 251
- CONFIGURATION AND DATA 251
- BUFFERING 251
- B.6 INPUT DATA FILTERS 252
- B.7 PROGRAM EXAMPLES 254
- CONTROL PORT 5 CONTROL PORT 5 255
- CR23X CR23X 255
- 06: P End Table 1 259
- C.1 TELECOMMUNICATIONS 269
- COMMAND WITH BINARY 269
- RESPONSES 269
- C.2 FINAL STORAGE FORMAT 272
- C.3 GENERATION OF SIGNATURE 273
- COMMANDS TO TRANSFER 274
- PROGRAM WITH COMPUTER 274
- APPENDIX E. ASCII TABLE 277
- F1. FUNCTION 279
- F2. INSTRUCTION DETAILS 279
- TELECOMMUNICATIONS) 283
- G.3 CR23X PROGRAMMING 285
- APPENDIX H 295
- H.4 REMOTE DATALOGGER 297
- PROGRAMMING 297
- 05: P86 Do 298
- AND CR23X MANUALS 301
- AD1 Major Differences 303
- AD3.1 Programming changes 304
- Section 12 307
- TABLE DATA ADDENDUM 308
- OV4. PROGRAMMING THE CR10X 309
- 32 converts the 313
- 03:P84 Data Table Instruction 314
- DATALOGGER 316
- COMPUTER 316
- SECTION 1. FUNCTIONAL MODES 317
- STATUS - ∗B 319
- 1.7 ∗C MODE -- SECURITY 319
- 1.8 ∗D MODE – TRANSFER 319
- PROGRAMS, GENERAL SETTINGS 319
- 1.9 *9 DATA TABLES SIZES 323
- 2.1 FINAL STORAGE AND DATA 325
- 2.2 DATA OUTPUT FORMAT AND 327
- RANGE LIMITS 327
- KEYBOARD/DISPLAY *7 MODE 327
- LOOP TO RUN AM416 MULTIPLEXER 333
- 02: P86 Do 334
- 06: P5 AC Half Bridge 334
- 07: P95 End 334
- TO COUNT SWITCH CLOSURES 335
- (RAIN GAGE) 335
- 8.5 SDM-A04 ANALOG OUTPUT 336
- Section 12. Program Control 345
- Instructions 345
- Security 350
- Remote Location/Coil/Register 350
- Remote Location 351
- Local Location 351
- Send Message (P192) 352
- Message Type 353
- Number of Remotes 354
- First Remote Address 354
- Time into Transmit Interval 354
- Transmit Interval 354
- Swath to Receive 355
- Seconds Until Transmit (P194) 356
- Swath to Receive From Master 358
- Swath to Send 358
- First Location to Send 358
- Force Route (P197) 359
- Set Setting (P198) 359
- Result Location 360
- Beacon Intervals 361
- Neighbor Filter 362
- CR23X INDEX 363
Produits connexes et manuels pour Mesure, test et contrôle Campbell CR23X
(38 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels