Campbell CDM-VW300 Series Manuel Page 8
- Page / 122
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Table of Contents
F. Thermistor Information........................................... F-1
F.1 Converting Resistance to Temperature.............................................F-1
F.1.1 Resistance Conversion Example – Geokon Sensor...................F-1
F.2 Accuracy and Resolution..................................................................F-1
G. CRBasic Program Library ......................................G-1
G.1 Dynamic Measurements .................................................................. G-1
G.1.1 20 Hz Measurement Example — One CDM-VW300, Two
Channels ............................................................................... G-1
G.1.2 20 Hz Measurement Example — One CDM-VW305, Eight
Channels ............................................................................... G-2
G.1.3 20 Hz Measurement Example — Three CDM-VW305s, 24
Channels ............................................................................... G-4
G.1.4 20 Hz Measurement Example — Six CDM-VW305s, 48
Channels ............................................................................... G-5
G.1.5 50 Hz Measurement Example — One CDM-VW300, Two
Channels ............................................................................... G-8
G.1.6 50 Hz Measurement Example — One CDM-VW305, Eight
Channels ............................................................................... G-9
G.1.7 50 Hz Measurement Example — Three CDM-VW305s, 24
Channels ............................................................................. G-11
G.1.8 50 Hz Measurement Example — One CDM-VW300, Two
Channels, Rainflow Histogram........................................... G-12
G.1.9 50 Hz Measurement Example — One CDM-VW305, Eight
Channels, Rainflow Histogram........................................... G-14
G.1.10 50 Hz Diagnostic Example — One CDM-VW300, Two
Geokon 4000 Sensors with FieldCal() ................................ G-15
G.1.11 50 Hz Measurement Example — One CDM-VW300, Two
Geokon 4000 Sensors with FieldCal() ................................ G-17
G.1.12 50 Hz Measurement Example — One CDM-VW300, Two
Geokon 4000 Sensors with FieldCal() and CardOut() to
CF ....................................................................................... G-19
G.1.13 50 Hz Measurement Example — One CDM-VW300, Two
Geokon 4000 Sensors with FieldCal() and TableFile() to
CF ....................................................................................... G-21
G.1.14 100 Hz Measurement Example — One CDM-VW300, Two
Channels ............................................................................. G-23
G.1.15 100 Hz Measurement Example — One CDM-VW305,
Eight Channels.................................................................... G-24
G.2 Static Measurements...................................................................... G-25
G.2.1 1 Hz Measurement Example — One CDM-VW300, Two
Channels ............................................................................. G-25
G.2.2 1 Hz Measurement Example — One CDM-VW305, Eight
Channels ............................................................................. G-26
Figures
4-1. Two-channel CDM-VW300 wiring panel........................................... 3
4-2. Eight-channel CDM-VW305 wiring panel.......................................... 4
4-3. Measurement speeds of the AVW200 and CDM-VW300 analyzers .. 4
4-4. Single-coil vibrating-wire sensor including coil and thermistor
outputs.............................................................................................. 5
4-5. Laboratory-mode measurement system diagram................................. 5
4-6. Field-mode data-acquisition system diagram ...................................... 6
iv
- CDM-VW300 Series 1
- Dynamic Vibrating-Wire 1
- Analyzers 1
- Warranty 3
- Assistance 4
- Table of Contents 5
- Figures 8
- Wire Analyzers 11
- 2. Cautionary Statements 12
- 3. Initial Inspection 12
- 4. Overview 13
- 4.2 Measurement Rates 14
- 4.4 Laboratory Mode 15
- 4.5 Field Mode 15
- 4.6 Data Uses 16
- 5. Specifications 17
- 5.2 Specifications 18
- 6. Installation 20
- 6.2 Field-Mode Installation 28
- Offset 29
- CDM_VW300Config() 34
- CDM_VW300Dynamic() 34
- CDM_VW300Static() 34
- 7. System Operation 36
- 7.1.2 Using DVWTool 37
- fields 38
- 7.1.3 Using DevConfig 39
- 7.2 Using the Datalogger 40
- 7.4 Using Power Supplies 41
- 7.5.1 Device Name 44
- 7.5.2 CPI Bus Speed 44
- ) allow 46
- 7.6 Sensor Selection 47
- 7.7 System Connections 47
- Shield / Sensor Ground 48
- Vibrating-Wire Sensor 48
- 7.8 Operating System 56
- 7.9 Power-Up Sequence 56
- 7.10 CRBasic Programming 57
- RF7, RF8) 58
- CPISpeed(BitRate) 58
- 7.11 System Adjustments 59
- 7.12 System Validation 59
- 8. Troubleshooting 63
- 8.4 Filtering Harmonics 64
- 8.5 Diagnostic Outputs 64
- (DiagCode AND 256) 67
- (DiagCode AND 512) 68
- (DiagCode AND 1024) 68
- (DiagCode AND 2048) 68
- 8.6 Factory Default Reset 69
- 9. Glossary 70
- Interface 75
- B.4 Specifications 77
- C.1.1 Power 79
- C.1.2 Interconnect Cable 79
- C.2 Distributed Architecture 81
- Thermistor 84
- 52611099 87
- F.2 Accuracy and Resolution 89
- G.1 Dynamic Measurements 93
- Channels 100
- output frequency 102
- Channels, Rainflow Histogram 104
- reading to obtain 109
- G.2 Static Measurements 117
Produits connexes et manuels pour Mesure, test et contrôle Campbell CDM-VW300 Series
Mesure, test et contrôle Campbell TDR Manuel
(28 pages)
(28 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels