Campbell CR5000 Spécifications Page 111
- Page / 238
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 6. Data Table Declarations and Output Processing Instructions
6-17
The difference between the closed and open form is shown in the following
example for temperature values:
Lower range limit 10° C
Upper range limit 30° C
Number of bins 10
Closed Form Open Form
Range of first bin 10 to <12° < 12°
Range of last bin 28 to <30° > 28°
Parameter
& Data Type
Enter
BinSelect
Variable or
Array
The variable that is tested to determine which bin is selected. The histogram 4D
instruction requires an array dimensioned with at least as many elements as
histogram dimensions.
DataType
A code to select the data storage format.
Constant
Alpha Code Numeric Code Data Format
IEEE4 24 IEEE 4 byte floating point
FP2 7 Campbell Scientific 2 byte floating point
DisableVar
Constant,
Variable, or
Expression
A non-zero value will disable intermediate processing. Normally 0 is entered so all inputs
are processed. For example, when the disable variable is
≠
0 the current input is not
included in the histogram. The histogram that is eventually stored includes the inputs that
occurred while the disable variable was 0.
Value Result
0 Process current input
≠
0 Do not process current input
Bins
Constant
The number of bins or subranges to include in the histogram bin select range. The width
of each subrange is equal to the bin select range (UpLim - LowLim) divided by the
number of bins.
Form
Constant
The Form argument is 3 digits - ABC
Code Form
A = 0 Reset histogram after each output.
A = 1 Do not reset histogram.
B = 0 Divide bins by total count.
B = 1 Output total in each bin.
C = 0 Open form. Include outside range values in end bins.
C = 1 Closed form. Exclude values outside range.
101 means: Do not reset. Divide bins by total count. Closed form.
WtVal
Constant or
Variable
The variable name of the weighted value. Enter a constant for a frequency distribution of
the BinSelect value.
LoLim
Constant
The lower limit of the range covered by the bin select value.
UpLim
Constant
The upper limit of the range of the bin select value.
- CR5000 Measurement and 1
- Control System 1
- Warranty and Assistance 2
- TABLE OF CONTENTS 3
- APPENDIX 4
- CR5000 MICROLOGGER 6
- OV2.1 Memory 9
- OV2.3 Data Tables 10
- OV3.2 PC9000 Installation 10
- OV3.3.1 File 13
- OV3.3.2 Edit 13
- OV4. Keyboard Display 15
- OV4.1 Data Display 16
- OV4.1.1 Real Time Tables 17
- CR5000 Overview 18
- OV4.2 Run/Stop Program 20
- OV4.3 File Display 21
- OV4.3.1 File: Edit 22
- OV4.4 Configure Display 23
- OV5. Specifications 24
- 1.2 Power Requirements 25
- 1.3 CR5000 Power Supplies 26
- 1.4 Solar Panels 28
- BOOST REGULATOR 29
- 1.7 CR5000 GROUNDING 30
- CR5000 ICROLOGGER 31
- 1.10 Maintenance 36
- BATTERY2 38
- (datalogger/cr5000) 38
- 2.1 Data Storage in CR5000 41
- 2.2 Internal Data Format 42
- 2.3 Data Collection 43
- 2.3.1.1 File Type 44
- 2.3.1.2 Collection Method 44
- 2.3.1.3 Table Selection 45
- 2.3.1.4 File Control 45
- 2.3.2 RealTime Write File 46
- 2.3.3 Logger Files Retrieve 47
- 2.3.4 Via PCMCIA PC Card 47
- 2.4 Data Format on Computer 50
- 2.4.2 TOA5 ASCII File Format 51
- 3.1.1 Voltage Range 55
- 3.1.4 SettlingTime 57
- 3.1.5 Integration 57
- Measurements 58
- 3.3 Signal Settling Time 59
- 3.4.1 Error Analysis 62
- Thermocouple Limits of Error 65
- Noise on Voltage Measurement 67
- Error Summary 69
- CR5000 Junction Box 70
- 3.7 Pulse Count Measurements 74
- 3.8 Self Calibration 75
- 4.1 Format Introduction 77
- 4.2 Programming Sequence 78
- 4.3 Example Program 80
- CallTable Temp 82
- 4.4 Numerical Entries 83
- 4.6 Flags 84
- 4.7 Parameter Types 85
- 'Calibration factors: 86
- Station Name 91
- Sub, Exit Sub, End Sub 91
- Subroutine Example 93
- 6.1 Data Table Declaration 95
- 6.2 Trigger Modifiers 96
- OpenInterval 97
- FillStop 99
- 6.3 Export Data Instructions 102
- TableOption 103
- BufferControl 103
- Highlimit, MinAmp, Form) 118
- Code Form 119
- Constant 119
- Measured raw data: 123
- 7.8 Digital I/O 128
- 7.9 Peripheral Devices 128
- 7.1 Voltage Measurements 129
- Integ, Mult, Offset) 130
- 7.3 Half Bridges 131
- 7.4 Full Bridges 134
- 7.5 Current Excitation 137
- 7.7 Self Measurements 141
- Calibrate (Dest, AllRanges) 142
- ± 10 mV) and resolution 146
- Silicon diodes 146
- . Resistor 146
- PortGet (Dest, Port) 147
- PortSet (Port, State) 148
- Pulse Channel 149
- PulseCountReset 151
- ReadIO (Dest, Mask) 151
- TimerIO 153
- WriteIO (Mask, Source) 154
- SDMAddress 156
- SEG TSEG q22 158
- Parameter 160
- & Data Type 160
- Description 165
- Result 167
- SDMSpeed (BitPeriod) 168
- SDMTrigger 168
- ValuesPerRep 170
- This is a blank page 172
- Instructions 173
- ACOS (Source) 174
- ASIN (Source) 175
- ATN (Source) 176
- AvgSpa (Dest, Swath, Source) 177
- Cos (Source) 179
- CosH (Source) 179
- Variable or 180
- Frac (Source) 183
- Int, Fix 186
- Log (Source) 187
- LOG10 (number) 187
- MemoryTest 188
- MaxSpa (Dest, Swath, Source) 188
- MinSpa (Dest, Swath, Source) 189
- Move (Dest, Swath, Source) 190
- Randomize 194
- RealTime 195
- RectPolar (Dest, Source) 196
- RMSSpa (Dest, Swath, Source) 197
- RND (Source) 197
- Sgn (Source) 201
- Sin (Source) 201
- SinH (Source) 202
- Sqr (Source) 202
- StdDevSpa 203
- Tan (Source) 203
- TANH (Source) 204
- Derived Math Functions 205
- Section 9. Program Control 207
- CallTable 208
- Data, Read, Restore 209
- ClockSet 209
- Delay (Option, Delay, Units) 210
- FileManage 212
- FileMark (TableName) 213
- For ... Next Statement 213
- Power Off 217
- RunDLDFile 218
- Reset Table 219
- Select Case Statement 221
- Slow Sequence 223
- While…Wend 227
- This is a blank 236
Produits connexes et manuels pour Mesure, test et contrôle Campbell CR5000
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.174 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels