Campbell CR510 Manuel de l'opérateur Page 123
- Page / 264
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SECTION 10. PROCESSING INSTRUCTIONS
10-3
*** 43 ABS(X) ***
FUNCTION
Take the absolute (ABS) value of X and place
the result in an input location.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: 4 Dest. input location for
ABS(X) [Z]
Input locations altered: 1
*** 44 FRACTIONAL VALUE OF X ***
FUNCTION
Take the fractional (FRAC) value (i.e., the non-
integer portion) of X and place the result in an
input location, e.g, FRAC (1.5) = 0.5.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: 4 Dest. input location for
FRAC(X) [Z]
Input locations altered: 1
*** 45 INTEGER VALUE OF X ***
FUNCTION
Take the integer (INT) value of X and place the
result in an input location, e.g., FRAC (1.5) = 1.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: 4 Dest. input location for
INT(X) [Z]
Input locations altered: 1
*** 46 X MOD F ***
FUNCTION
Do a modulo divide of X by F and place the
result in an input location. X MOD F is defined
as the REMAINDER obtained when X is divided
by F (e.g., 3 MOD 2 = 1). X MOD 0 returns X.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: FP Fixed divisor [F]
03: 4 Dest. input loc. For X
MOD F [Z]
Input locations altered: 1
*** 47 X
Y
***
FUNCTION
Raise X to the Y power and place the result in
an input location.
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: 4 Input location of Y [Y]
03: 4 Dest. input location for
X
Y
[Z]
Input locations altered: 1
*** 48 SIN(X) ***
FUNCTION
Calculate the sine of X (X is assumed to be in
degrees) and place the result in an input
location. The cosine of a number can be
obtained by adding 90 to the number and taking
the sine (COSX = SIN (X + 90)).
PARAM. DATA
NUMBER TYPE DESCRIPTION
01: 4 Input location of X [X]
02: 4 Dest. input location for
SIN(X) [Z]
Input locations altered: 1
*** 49 SPATIAL MAXIMUM ***
FUNCTION
Find the spatial maximum (SPA MAX) value of the
given set or SWATH of input locations and place
the result in an input location. To find the input
location where the maximum value occurs, add
1000 to the input location number destination
selected [Z] and enter this modified location
number as Parameter 03. The input location ID of
the maximum value observed will then be stored in
destination [Z] plus 1.
- CR510 DATALOGGER 1
- OPERATOR'S MANUAL 1
- WARRANTY AND ASSISTANCE 3
- TABLE OF CONTENTS 5
- DATA RETRIEVAL/COMMUNICATION 6
- PROGRAM EXAMPLES 6
- INSTRUCTIONS 7
- INSTALLATION 7
- APPENDICES 8
- FEATURES OF CR510 9
- This is a blank page 10
- SELECTED OPERATING DETAILS 11
- CAUTIONARY NOTES 12
- CR510 DATALOGGER OVERVIEW 13
- OV2. MEMORY AND PROGRAMMING 15
- CONCEPTS 15
- OV4. PROGRAMMING THE CR510 21
- CR510 OVERVIEW 30
- ARRAYS, AND MEMORY POINTERS 45
- 3.1 PARAMETER DATA TYPES 49
- 3.2 REPETITIONS 49
- 3.4 INDEXING INPUT LOCATIONS 49
- 3.5 VOLTAGE RANGE AND 50
- OVERRANGE DETECTION 50
- 3.6 OUTPUT PROCESSING 50
- PROGRAM CONTROL 51
- 3.8 PROGRAM CONTROL LOGICAL 52
- CONSTRUCTIONS 52
- 3.9 INSTRUCTION MEMORY AND 55
- EXECUTION TIME 55
- 3.10 ERROR CODES 59
- 4.1 ON-LINE DATA TRANSFER 61
- INSTRUCTION 96 61
- 4.4 STORAGE MODULE 64
- 5.1 TELECOMMUNICATIONS 67
- COMMANDS 67
- 6.1 PIN DESCRIPTION 71
- 6.2 ENABLING AND ADDRESSING 72
- PERIPHERALS 72
- 6.3 RING INTERRUPTS 73
- 6.6 SYNCHRONOUS DEVICE 74
- COMMUNICATION 74
- 6.7 MODEM/TERMINAL AND 75
- COMPUTER REQUIREMENTS 75
- 7.1 SINGLE ENDED VOLTAGE 79
- 107 TEMPERATURE PROBE 79
- 7.2 DIFFERENTIAL VOLTAGE 79
- MEASUREMENT 79
- 7.4 ANEMOMETER WITH 81
- PHOTOCHOPPER OUTPUT 81
- LONG LEADS 82
- FULL BRIDGE 86
- 7.12 NONLINEAR THERMISTOR IN 90
- HALF BRIDGE 90
- CR510 & AVW1 93
- 12 V or 5 V 94
- 7.14 4 TO 20 MA SENSOR USING 95
- CURS100 TERMINAL INPUT 95
- SYNCHED TO REAL TIME 99
- PORTS (RAIN GAGE) 99
- 8.5 CONVERTING 0-360 WIND 100
- DIRECTION OUTPUT TO 0-540 FOR 100
- STRIP CHART 100
- - SAVING DATA PRIOR TO EVENT 101
- zero yields 110
- SEQUENCE 145
- 13.2 SINGLE-ENDED AND 146
- DIFFERENTIAL VOLTAGE 146
- MEASUREMENTS 146
- LENGTH ON THE SIGNAL SETTLING 147
- 13.4 BRIDGE RESISTANCE 156
- 13.5 RESISTANCE MEASUREMENTS 160
- REQUIRING AC EXCITATION 160
- 13.6 CALIBRATION PROCESS 161
- 14.1 PROTECTION FROM THE 163
- ENVIRONMENT 163
- 14.2 POWER REQUIREMENTS 163
- SUPPLIES 164
- 12V ALKALINE BATTERY PACK 165
- DESI PAK 166
- 14.7 GROUNDING 168
- 14.8 TERMINAL STRIP 169
- FOR SWITCHING RELAYS 169
- 14.10 MAINTENANCE 171
- APPENDIX A. GLOSSARY 173
- B.1 TELECOMMUNICATIONS 177
- COMMAND WITH BINARY 177
- RESPONSES 177
- B.2 FINAL STORAGE FORMAT 179
- APPENDIX C. ASCII TABLE 183
- D.1 INTRODUCTION 185
- D.2 EXAMPLE PHONE CALLBACK 185
- PROGRAM BASED ON A CONDITION 185
- AND IT’S COMPUTER SETUP 186
- APPENDIX E 189
- E.4 REMOTE DATALOGGER 191
- PROGRAMMING 191
- F.1 TERMINOLOGY 193
- F.2 COMMUNICATIONS AND 193
- COMPATIBILITY 193
- F.3 MORE ON MODBUS 194
- AND CR23X MANUALS 199
- AD1 Major Differences 201
- AD3.1 Programming changes 202
- Section 12 205
- TABLE DATA ADDENDUM 206
- OV4. PROGRAMMING THE CR10X 207
- OV5. PROGRAMMING EXAMPLES 209
- 32 converts the 211
- 03:P84 Data Table Instruction 212
- OV6. DATA RETRIEVAL OPTIONS 213
- DATALOGGER 214
- COMPUTER 214
- SECTION 1. FUNCTIONAL MODES 215
- STATUS - ∗B 217
- 1.7 ∗C MODE -- SECURITY 217
- 1.8 ∗D MODE – TRANSFER 217
- PROGRAMS, GENERAL SETTINGS 217
- 1.9 *9 DATA TABLES SIZES 221
- 2.1 FINAL STORAGE AND DATA 223
- 2.2 DATA OUTPUT FORMAT AND 225
- RANGE LIMITS 225
- KEYBOARD/DISPLAY *7 MODE 225
- 8.1 COMPUTATION OF RUNNING 229
- 8.2 RAINFALL INTENSITY 230
- 8.3 USING CONTROL PORTS AND 231
- LOOP TO RUN AM416 MULTIPLEXER 231
- TO COUNT SWITCH CLOSURES 233
- (RAIN GAGE) 233
- 8.5 SDM-A04 ANALOG OUTPUT 234
- MULTIPLEXER TO STRIP CHART 234
- Section 12. Program Control 243
- Instructions 243
- Security 248
- Remote Location/Coil/Register 248
- Remote Location 249
- Local Location 249
- Send Message (P192) 250
- Message Type 251
- Number of Remotes 252
- First Remote Address 252
- Time into Transmit Interval 252
- Transmit Interval 252
- Swath to Receive 253
- Seconds Until Transmit (P194) 254
- Swath to Receive From Master 256
- Swath to Send 256
- First Location to Send 256
- Force Route (P197) 257
- Set Setting (P198) 257
- Result Location 258
- Beacon Intervals 259
- Neighbor Filter 260
- LIST OF TABLES 261
- LIST OF FIGURES 263
Produits connexes et manuels pour Mesure, test et contrôle Campbell CR510
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels